Zhuohang Precision Machining Factory

Online CNC Machining Quality Control

A capability statement is worthless without a control chart. On a representative length characteristic (76.1–76.5 mm), our SPC shows Cpk 1.851 (one characteristic on one part, not a blanket capability claim) against an initial-study target of Ppk ≥ 1.67, with general characteristics held to Cpk ≥ 1.33. That is a measured result, and the reason a batch does not come back for rework.

Read a capability number for what it does, not what it advertises. Cpk 1.851 (one characteristic on one part, not a blanket capability claim) on a length characteristic means the process runs deep inside the tolerance band, with margin on both sides, not just scraping by. Ask for the control chart behind the number: a single Cpk with no chart is a claim, while a stable, centered chart is evidence.

How is a part inspected before it ships?

Zhuohang MES production management dashboard, Zhuohang Precision Machining Factory, Dongguan, China Zhuohang CNC, Zhuohang Precision Machining Factory, Dongguan, China

The inspection bench is the same class of equipment a buyer would use to audit us, and the results are documented.

EvidenceWhat it protects
XRF material checkA mixed or mislabeled alloy caught at the door
CMM first-article reportDimensional proof before the lot ships
SPC chart (Ppk ≥ 1.67 at the initial study on key characteristics)Process drift caught mid-run
Mill certificate with heat numberTraceability back to the heat

The bench is only as good as the report it writes. A CMM produces a list of measured values against the drawing, an SPC chart produces a computed Cpk, and an XRF reading produces a material composition matched to the mill certificate. Those are the documents you can audit — the same documents a buyer would ask for on arrival. The inspection is the evidence, and a part that ships with the evidence is a part you do not have to re-inspect at your own dock, which is a saving in your own time and risk.

How is material verified before it is cut?

Quality inspection at Zhuohang Precision Machining Factory for online CNC machining
Inspection that protects cost

Incoming bar is XRF-checked against its mill certificate so a mixed or mislabeled lot is caught at the door, and a material certificate with a heat number follows the batch. A wrong alloy is the most expensive failure there is — catching it at the door costs nothing; catching it in the field costs everything.

The check closes the loop on the material lever in the cost stack. If you specify 6061-T6 or 316, you are paying for that alloy, not for whatever the warehouse happened to have; the XRF reading against the mill certificate makes the transaction honest, and the heat number makes it traceable. A part that can be traced back to its heat is a part that can be isolated on a failure, instead of forcing you to treat an entire order as suspect and replace it wholesale.

Can the shop provide a PPAP package?

For automotive and regulated buyers, a PPAP package proves the process is under control. Our APQP/PPAP evidence includes process flow charts, control plans, SPC charts, and PFMEA — the same discipline that keeps a production run from turning into a rework bill.

PPAP is not a document you buy; it is the process's paper trail. The flow chart, control plan, SPC chart, and PFMEA together prove the process was thought through before the first article, not reverse-engineered after a rejection. For a regulated buyer, that paper is worth more than a lower headline price, because it is what an auditor will ask for later.

The same discipline protects a non-automotive buyer, because a process that is thought through is a process that does not drift into rework. A control plan that names which characteristic is checked, how often, and with what gauge is a cost plan for quality — it spends inspection where the risk is and saves it where the process is already proven. The paper is the proof that the cost of quality was planned, not discovered, which is the same discipline that keeps every other cost lever honest.

How do you interrogate a shop's quality claims?

What does Cpk actually tell you about cost?

Cpk is a number that measures how much margin a process has between its output and the tolerance limits. A process that runs deep inside the band has a high Cpk; a process that scrapes the limits has a low one. On a representative length characteristic (76.1–76.5 mm), the shop's SPC shows Cpk 1.851 (one characteristic on one part, not a blanket capability claim) against an initial-study target of Ppk ≥ 1.67, with general characteristics held to Cpk ≥ 1.33. In plain terms, that is a process running well inside its limits with margin on both sides, not one scraping by.

The cost meaning is direct: a capable process produces fewer rejects, and rejects are what turn a cheap part into an expensive one. When a process holds Ppk ≥ 1.67 initial, a batch can be trusted on a sampling plan instead of 100% inspection, which cuts the inspection bill. When the process drifts, the control chart catches it mid-run, before it becomes a full-batch rework. That is why a Cpk chart is worth more than a tolerance claim — it is evidence that the part was measured right before it shipped, and the cost of catching it early is a fraction of the cost of finding it at your dock.

How does traceability lower the cost of a failure?

Every batch produces data, which lot, which machine, which operator, which material heat. A shop that records that chain can isolate a problem to a single lot and contain it; a shop that does not has to treat an entire order as suspect. The MES/ERP system records the full chain on every lot, from raw material source and usage through process parameters, machine data, production batch, machining time, operator, and inspection results.

The cost case is containment. When a non-conformance surfaces, traceability tells you exactly which parts are affected, so you replace one lot instead of scrapping a whole order and re-running it. For a regulated buyer that is a requirement; for everyone else it is cheap insurance against the costliest failure there is — the one where you cannot prove which parts are bad. The chain begins with an XRF check of incoming material against its mill certificate and runs on every job, not just the ones that demand it.

What does a first-article inspection report contain?

A first-article inspection (FAI) is the proof that the process makes the part before the batch runs. It measures every dimension and every callout on the first piece against the drawing, and writes the measured value next to the nominal. If you receive an FAI, you know the process was validated before volume, not discovered during it.

The report is the paper trail of the tolerance lever. Each tight dimension shows its measured value and whether it fell in band; each general note shows the default was respected. When the first article passes, the batch can proceed on a sampling plan; when it does not, the process is corrected before a hundred wrong parts are made. The FAI is the cheapest moment to catch a problem there is — one part, at the machine, before the run — and a shop that ships it with the lot is pricing the proof, not the hope.

What this shop actually runs

We machine every part in our own 6,800 m² plant in Dongguan, China, on 100+ CNC machines with 100+ staff. The machine list by category:

  • 5-axis machining centres (10+) - Mazak VARIAXIS I-600 (510/910/510 mm travel, 12,000 rpm, 22 kW, 71.6 N·m, 30-tool BT40) and Mazak INTEGREX I-250H S (B-axis 0.0001°, 24 kW, 124 N·m, 38-tool HSK-A63). Intended for compound-angle parts, single-setup multi-face prismatic work, and aerospace fittings where datum transfer loss is unacceptable.
  • 3-axis / 4-axis machining centres (50+) - Brother SPEEDIO S500Z2N / S700Z2N (10,000 rpm, 14/21-tool ATC, 0.7 s tool-to-tool, Z-axis 2.2 G) and Mazak VCE-430A L / VCE-570C L (10,000 rpm, 118 N·m, 24-tool ATC). Intended for prismatic parts, plates, brackets, housings.
  • Swiss-type turning centres (10+) - Citizen Cincom A20-3F7 (Φ20 mm, 10,000 rpm), TSUGAMI B0206-III / B0205-III (Φ20 mm, 0.1 µm), STAR SR-32JII / SR-32J Type N (Φ32 mm, 8,000 rpm). Intended for long, slender rotational parts at ±0.002 mm.
  • CNC turning centres (20+) - HEADMAN T70M/1250 (720 mm swing, 117 mm bore, 3,000 rpm, BMT75 12-station turret). Intended for shafts, bushings, flanges up to ±0.002 mm.
  • Wire EDM (5+) - Sodick AQ535L (550/350/300 mm travel, ±20° taper, 800 kg workpiece). Intended for hardened tool steel, internal splines, sharp internal corners that milling cannot reach.
  • Inspection: Hexagon CMM + 20+ gauges - Hexagon CMM for coordinate measurement, plus vision system, profilometer, hardness tester, coating thickness gauge, XRF for material verification. The 10:1 rule (gauge 10x more accurate than the band) is applied to every feature.
  • Machine highlights - VARIAXIS I-600: one-setup multi-face 5-axis + MAZA-CHECK auto-calibration; INTEGREX I-250H S: DONE-IN-ONE mill-turn, B-axis 0.0001° + Ai thermal shield; SPEEDIO S500Z2N / S700Z2N: Z-axis 2.2 G + 0.7 s ATC; Swiss-type: guide-bush switchable + 0.1 µm resolution.

Tolerance: ±0.003 mm CNC milling / ±0.002 mm CNC turning / ±0.002 mm grinding and wire EDM. Capability: Ppk >= 1.67 initial on key characteristics, Cpk >= 1.33 ongoing.

Certificates: ISO 9001:2015 (116024/A/0001/UK/En), IATF 16949:2016 (131941/A/0001/SM/En, with design clause 8.3 excluded, stated openly) and ISO 14001:2015 (116024/B/0001/UK/En), issued to Dongguan Zhuohang Ltd, registration 91441900MA4UWT6X39, founded 2005.

Where we ship: Austria, Belgium, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, the Netherlands, Spain, Sweden and the United Kingdom in Europe; Brazil, Canada, Mexico and the United States in the Americas; China, Israel, Japan, Singapore and Sri Lanka in Asia; Australia and New Zealand in Oceania; and South Africa in Africa — plus other countries and regions worldwide, shipped from our base in Dongguan, China.

Contact: Felipe Iglesias, [email protected], +86 13126536955.

Verify the quality that protects your cost

Email [email protected] or call +86 13126536955 and ask for the certificate numbers, a Cpk chart, and a material certificate.

Frequently Asked Questions

Why is quality the cheapest way to buy machining?

Rework and a recall cost far more than doing it right the first time. CMM inspection and SPC catch drift mid-run, before it becomes a full-batch rework, so the part that measures right is also the part that costs least.

Which certifications back the quality system?

ISO 9001:2015 (No. 116024/A/0001/UK/En), IATF 16949:2016 (No. 131941/A/0001/SM/En), and ISO 14001:2015 (No. 116024/B/0001/UK/En). The IATF 16949 scope excludes product design under Clause 8.3.

What process capability does the shop demonstrate?

In short, On a representative length characteristic (76.1–76.5 mm), the SPC shows Cpk 1.851 (one characteristic on one part, not a blanket capability claim) against an initial-study target of Ppk ≥ 1.67, with general characteristics held to Cpk ≥ 1.33. Read the tolerance band before you read the index.

How are parts inspected before they ship?

Critical dimensions are verified on Hexagon GLOBAL S CMMs, supported by a KEYENCE VK-X3000 laser microscope, a SURFCOM 1800D for surface finish, an XRF spectrometer for material, and hardness, coating-thickness, salt-spray, and tensile testers.

Can the shop provide PPAP and control plans?

Yes. The automotive-grade APQP/PPAP package is supported by process flow charts, control plans, SPC charts, and PFMEA, reflecting the IATF 16949 build-to-print discipline.

Standards referenced on this page

  • IATF 16949:2016 — Automotive quality management system standard
  • ASTM A582/A582M-12 — Standard Specification for Free-Machining Stainless Steel Bars
  • ISO 14001 — Environmental management systems — Requirements with guidance for use